MadAboutTools stock a range of Drywall Screws from 3.5 x 25mm to 4.8 x 150mm!!

These screws are Zinc plated so no more rust marks after skimming.

The Low Profile Torx drive head is great for Warm Roofing and with lengths up to 400mm you can fix any thickness of Insulation. 

They have an Olive Green finish which is able to withstand 1000 hrs of salt spray so are ideal for external applications.

The Screw has a Sharp point with a Slash to help penetration and has Patented Molecular Lubrication to increase insertion speed.

The Wafer Head In-Dex screws are available from 95mm up to 400mm

These fixings enable you to easly install heavy items such as Radiators and Flat Screen TV's onto a plaster board wall. The Gripit Fixing has a higher load carring capacity than any other plaster board fixing and will even work in ceilings. Their patented design allows the load to be spead over a large area thanks to its extendable 'wings'.

No special tools are required, all you need is the correct size flat wood bit and a small straight screwdriver. If you purchase our complete Gripit-Kit then you get all 4 sizes of fixing, a selection of screws to suit the fixings and the correct size flat wood bits.

Go to GRIPIT Fixings.......

This is a limited offer so get them while you can!

EYC199 14.4V TWIN PACK - DRILL DRIVER AND IMPACT DRIVER - Now only £239 + vat

Plus many more....

Limited Stocks available so get in quick!

Mad About Tools.co.uk have added a TOP TIPS section to their website to help customers get the most out of their Tools. The instructions that come with Power Tools do not normally tell you how to get the best out of the machine which is where this section will hopefully help. This section will grow over time and with the assistance of their customers who can submit their own Tips for inclusion. Check the MadAboutTools.co.uk website frequently to check for updates to this section.

Here are a few Top Tips which will help you get the best out of the Machine and keep it going for many years. 

Top Tips -

• When using this power tool do not place too much pressure on the tool, let the tool do the work.
• Keep the tool moving whilst making the cut - this helps to remove the spoil and stops the blades jamming in the cut.
• As the teeth are wider than the blade you can use the side of the teeth to help make the cut wider when pointing.
• Keep the Blade Teeth in tip top condition by regularly sharpening them with the Arbortech A16054 Diamond Blade mounted on a 4" or 4.5" Angle Grinder. 
• Regularly check the tightness of the screws holding the blades. If they become loose the holes can become oval which will make the blades unusable!
• Only use the supplied 'Ian' (Hex) Key to tighten the blade screws as when the loop on the Key closes then screws are done up to the correct torque.
• Replace any damaged Blade Retaining screws with only genuine Arbortech replacments as they are specially machined to aid blade retension..
• Give the machine a good vacuum out after use in a dust environment to help reduce brush and belt wear.
• Keep the AS170 in its bag to help reduce the possibility of damage whilst in the van - the blades can be damaged if knocked and once bent they cannot be used. Replacements are from £60.

Whilst you're ordering this fantastic and unique Power Tool take a look at the range of additional Blades that are available for a range of tasks. All these Blades are at very competitive prices.

So pick yourself up a bargin and get that pointing or wall repair job done in record time saving you money and keeping you and your employees safe!! (when compared to using a 12" spinning disc or Club Hammer and Chisels).

This is THE tool which will SAVE you MONEY. You will be able to Cut Out Bricks and Mortar far quicker, safer and with less damage than any other method. Those customers who have been able to look past the expense of the initial outlay for the machine and blades have seen the potential savings and have then used this tool to MAKE MONEY.

Make the decision NOW as this price cannot be maintained for much longer.

Tips -

When using this power tool do not place too much pressure on the tool, let the tool do the work.

Keep the tool moving whilst making the cut - this helps to remove the spoil and stops the blades jamming in the cut.

As the teeth are wider than the blade you can use the side of the teeth to help make the cut wider when pointing. 

Regularly check the tightness of the screws holding the blades. If they become loose the holes can become oval which will make the blades unusable!

Replace any damaged screws with only genuine Arbortech replaces and they are specially machined.

Give the machine a good vacuum out after use in a dust environment to help reduce brush and belt wear.

Hitachis' New Combi / Impact Driver Twin Pack (KC18DKL) with 2 x 4Ah Batteries for ONLY £299 + vat. 

We must be MAD !!! 

MadAboutTools.co.uk