You are viewing this site in staging mode. Click in this bar to return to normal site.

Jigs

  • Pocket Hole Jig

    Pocket Hole Jig

    Pocket Hole Jig
    PH/JIG

    For fast and accurate joining of timber and plywood giving strong instant joints.

    Solid hardened bushes with variable pitch of 29mm to 63mm.

    Use on timber, MDF, plywood and blockboard.

    Allows a variety of joints to be created individually.

    Uses square drive self tapping screws.

    Workpiece can be handled immediately after gluing & screwing creating time saving benefits. No clamps required.

    Includes:

  • 100 x Dome head screws
  • 1 x Face clamp
  • 1 x HSS drill bit with collar
  • 1 x 75mm Square drive bit
  • 1 x 150mm Square drive bit
£59.15
(ex. VAT)
  • Craft Dovetail Jig 300mm

    Craft Dovetail Jig 300mm

    Craft Dovetail Jig 300mm
    CDJ300

    An accurate and easy to use Dovetail Jig for a variety of elegant dovetail joints.

  • Cuts 12.7mm (1/2 inch) wide half blind dovetails or rebated dovetails in one operation.
  • Precision made laser cut zinc plated steel template with packing piece.
  • A Unibase and fine height adjuster may be required for certain makes of router.
  • A range of accessory templates are available for box joint, dowel and through dovetails.

    •  

    Includes:

    • 1 x 1/4" Shank TCT 104 degree dovetail cutter
    • 1 x 15.8mm Guide bush
    £99.26
    (ex. VAT)
  • Hinge Recessing Jig

    Hinge Recessing Jig
    (Single Piece)

    Hinge Recessing Jig
    HINGE/JIG

    The Hinge Jig is a portable template set designed for recessing hinges in wooden doors & frames.

    • It is easy to use with minimal setting-up time, completing the job both accurately & quickly.
    • Used on-site & in joinery shops to increase productivity with excellent results.
    • Four apertures for fire door requirements.
    • No need for marking out in the conventional way.
    • Quick & simple to set-up as the hinge is used as the pattern.
    • Clean & accurate recesses are achieved every time. Suitable for timber based doors & square butt hinges.
    • Use with a light duty router with 1/4 inch collet.
    • Long reach router cutter required, 12mm diameter with 70mm overall length.
    • Angled position slots to prevent creep.

     

    Includes:

    • 4 x Apertures
    • 2 x Bradawls with spacer
    • 1 x 16mm guide bush
    • 1 x T-Handle hex key
    • 1 x 4mm spacing gauge
    • 1 x Plastic storage tube
    £199.50
    (ex. VAT)
  • Mortise & Tenon Jig

    Mortise & Tenon Jig

    Mortise & Tenon Jig
    MT/JIG

    Enables mortise & tenons and dowel joints to be cut with a router.

    • Ideal for cabinet, chair and table.
    • CNC precision manufactured plates and body.
    • One set-up for both mortise and tenon giving perfectly fitting joints.
    • Fully adjustable for compound angle joints up to 45 degree.
    • Reversible templates to produce round and square end tenons.
    • Templates can be used for accurate dowelling applications.
    • Cuts mortise & tenon sizes of 1/4 inch (6.35mm) to 5/8 inch (15.9mm).
    • Guide bushes are included but cutters are required.
    • A Unibase may be required for certain makes & models of router.
    • All tenons are cut with a 5/8 inch diameter straight cutter (Ref. C026).
    • The width of the tenon is adjusted by using different guide bush diameters.
    • International PCT Appl No. PCT/GB02/00253.

    Includes:

    • 5 x Guide bushes
    • 4 x Clamps
    • 1 x Guide bush collar
    • 1 x Set-up Bar
    £179.46
    (ex. VAT)
  • Hinge Jig Two Part

    Hinge Jig Two Part
    (Two Piece) for easy handling c/w Fabric Case

    Hinge Jig Two Part
    H/JIG/A

    A two-part aluminium hinge jig portable template set designed for recessing hinges in wooden doors & frames.

    • It is easy to use with minimal setting-up time, completing the job both accurately & quickly.
    • Used on-site & in joinery shops to increase productivity with excellent results.
    • Four apertures for fire door requirements.
    • No need for marking out in the conventional way.
    • Quick & simple to set-up as the hinge is used as the pattern.
    • Clean & accurate recesses are achieved every time. Suitable for timber based doors & square butt hinges.
    • Use with a light duty router with 1/4 inch collet.
    • Long reach router cutter required, 12mm diameter with 70mm overall length.
    • Angled position slots to prevent creep.

     

    Includes:

    • 4 x Apertures
    • 2 x Bradawls with spacer
    • 1 x 16mm guide bush
    • 1 x T-Handle hex key
    • 1 x 4mm spacing gauge
    • 1 x Fabric storage case
    £209.54
    (ex. VAT)
  • Template Butt Hinge

    Template Butt Hinge

    Template Butt Hinge
    TEMP/BH/A

    A routing template that allows a router to create a hinge recess on a door.

    • Made from clear 8mm thick plastic.
    • Includes metal templates for 75mm and 100mm butt hinges.
    • Magnets in template frame to hold templates.
    • Cuts rounded corners which can be removed with a corner chisel or chisel.
    • Use on doors from 35mm to 44mm thick.
    • Requires 12mm diameter cutter and 30mm guide bush.
    • A user made batten 44mm x 34mm x 450mm is also needed.

     

    Specifications:

    Size:  214mm x 135mm x 8mm

    £35.28
    (ex. VAT)
  • Craft Dovetail Jig 600mm

    Craft Dovetail Jig 600mm

    Craft Dovetail Jig 600mm
    CDJ600

    An accurate and easy to use Dovetail Jig for a variety of elegant dovetail joints.

  • Cuts 12.7mm (1/2 inch) wide half blind dovetails or rebated dovetails in one operation.
  • Precision made laser cut zinc plated steel template with packing piece.
  • Adjustable offset stops.
  • A Unibase and fine height adjuster may be required for certain makes of router.
  • A range of accessory templates are available for box joint, dowel and through dovetails.

    •  

    Includes:

    • 1 x 1/4" Shank TCT 104 degree dovetail cutter
    • 1 x 15.8mm Guide bush
    £169.43
    (ex. VAT)
  • Worktop Jig 1000mm

    Worktop Jig 1000mm

    Worktop Jig 1000mm
    COMBI1002

    For up to 1000mm wide worktop now with cable tidy insert & circular hinge cut apertures.

    • A single male and female template in 16mm solid laminate.
    • Facility to join boards from 450mm to 1000mm wide.
    • Facility to cut 22.5 degree mitre corners for hob units.
    • Intergral template slots for rounding and mitring of peninsular worktop corners for cable tidy inserts and a circular concealed hinge aperture and 3/4 inch BSP holes for mixer taps.
    • Three alloy location bushes and a width-setting stop.
    • Colour coded pin location for quick and easy use.
    • Three bolt recess slots for connection bolts.
    • Cuts out of square joints (max. 3 degrees).

     

    • Jig requires:
    • A portable plunge router with 12.7mm (1/2 inch) shank capacity and minimum 1300 watts.
    • A template guide bush with 30mm outside diameter.
    • A TCT router cutter with 12.7mm (1/2 inch) diameter and 50mm (2 inch) cut length.
    • Two 100mm (4 inch) throat clamps.

     

    Includes:
    • 1 x Length Stop
    • 3 x Location Bushes

     
    £259.89
    (ex. VAT)
  • Worktop Jig 500-650mm Peninsular

    Worktop Jig 500-650mm Peninsular

    Worktop Jig 500-650mm Peninsular
    COMBI66

    A worktop jig, designed to enable all 1/2 inch shank plunge routers to cut precise butt & scribe joints in postform workstops.

    • Machined from hardwearing solid laminate.
    • Will produce a joint in 15 minutes including setting-up time.
    • Out-of-square joints can be accommodated.
    • Facilities to cut various widths of board and thicknesses up to 42mm.
    • Integral panel bolt connector recessing template with easy spanner access.
    • Width setting stop for accurate positioning.
    • Supplied with clear & comprehensive instructions for use.
    • A single male and female template in 16mm solid laminate.
    • Facility to join boards from 500mm to 650mm wide. Two bolt recess slot for connecting bolts.
    • Three alloy location bushes & width setting stop.
    • Cuts out of square joints (max. 3 degree).
     
    • Jig requires:
    • A portable plunge router with 12.7mm (1/2 inch) shank capacity and minimum 1300 watts.
    • A template guide bush with 30mm outside diameter.
    • A TCT router cutter with 12.7mm (1/2 inch) diameter and 50mm (2 inch) cut length.
    • Two 100mm (4 inch) throat clamps.

     

    Includes:

    • 3 x Location Bushes
    • 1 x Length Stop

     

    Specifications  

    combi66_dd.jpg
    Length 880 mm
    Width 233 mm
    Thickness 16 mm
    Weight 3.3kg

     

    £92.92
    (ex. VAT)
  • Worktop Jig 600mm

    Worktop Jig 600mm

    Worktop Jig 600mm
    COMBI600

    A worktop jig, designed to enable all 1/2 inch shank plunge routers to cut precise butt & scribe joints in postform workstops.

    • Machined from hardwearing solid laminate.
    • Will produce a joint in 15 minutes including setting-up time.
    • Facilities to cut various widths of board and thicknesses up to 42mm.
    • Integral panel bolt connector recessing template with easy spanner access.
    • Width setting stop for accurate positioning.
    • Supplied with clear & comprehensive instructions for use.
    • A single male and female template in 10mm solid laminate.
    • Offset widths 225,300,325,400,500,600 & 616mm. Integral single bolt recess slot for connecting bolts.
    • Three alloy location bushes.
     
    • Jig requires:
    • A portable plunge router with 12.7mm (1/2 inch) shank capacity and minimum 1300 watts.
    • A template guide bush with 30mm outside diameter.
    • A TCT router cutter with 12.7mm (1/2 inch) diameter and 50mm (2 inch) cut length.
    • Two 100mm (4 inch) throat clamps.

     

    Includes:  3 x Location Bushes

     

    Specifications  

    combi600_dd.jpg
    Length 845 mm
    Width 190 mm
    Thickness 10 mm
    Weight 1.8kg
    £55.85
    (ex. VAT)
  • Letterbox Jig

    Letterbox Jig

    Letterbox Jig
    LB/JIG

    Enables the cutting out of letterbox openings to be carried out quickly and accurately.

  • The size-adjusting jig ensures that template openings are always cut exactly square.
  • Made from cast aluminium and machined to a high standard.
  • Simple to set up and use.
  • Requires 1/2 inch diameter x 50mm cut length cutter. Unibase may be required for certain makes and models of router.

    •  

    Includes:
    • 1 x 30mm x 10mm spigot guide bush

     

    Specifications  
    Max aperture. 310 mm x 82 mm
    Min aperture. 210 mm x 46 mm
    £79.18
    (ex. VAT)
  • Stair Jig B

    Stair Jig B
    (Open Riser)

    Stair Jig B
    STAIR/B

    This template jig is a well proven means of routing out stair housings quickly and accurately.

    • Constructed from hard wearing solid laminate and includes a reversible fence for exact matching of stair strings and fully adjustable nosing piece.
    • Built-in heavy duty front clamp for quick clamping for each trench.
    • Adjustable to suit private and common stair angle pitch. The jig incorporates a stub riser to conform with building regulations.
    • All heavy duty routers over 1600 watts can be used.
    • Sub-base is pre-drilled to suit Trend/DeWalt/Elu 1/2 inch routers, for other makes the sub-base will have to be redrilled.
    • Please state make and model when ordering.
    • Router not included.

    Includes:

  • 1 x Adjustable reversible clamp bar
  • 1 x Reversible clamp bar
  • 1 x Sub-base
  • 1 x 24mm Guide Bush 
  • 1 x Line-up pin
  • 2 x Spanners
  • 1 x Line Up Guide bush
    • £148.11
    (ex. VAT)
  • Stair Jig A

    Stair Jig A
    (Closed Riser)

    Stair Jig A
    STAIR/A

    This template jig is a well proven means of routing out stair housings quickly and accurately.

    • Constructed from hard wearing solid laminate and includes a reversible fence for exact matching of stair strings and fully adjustable nosing piece.
    • Built-in heavy duty front clamp for quick clamping for each trench.
    • Adjustable to suit private and common stair angle pitch.
    • Standard TCT dovetail cutters are offered for various tread thicknesses.
    • All heavy duty routers over 1600 watts can be used.
    • Sub-base is pre-drilled to suit Trend/DeWalt/Elu 1/2 inch routers, for other makes the sub-base will have to be redrilled.
    • Please state make and model when ordering.
    • Router not included.

    Includes:

  • 1 x Sub-base
  • 1 x Adjustable reversible clamp bar
  • 1 x Reversible clamp bar
  • 1 x Nosepiece
  • 1 x Line-up pin & bush
  • 2 x Spanners
    • £148.11
    (ex. VAT)
  • Kitchen Worktop Jig 900mm

    Kitchen Worktop Jig 900mm

    Kitchen Worktop Jig 900mm
    KWJ900

    Tradesman ALL IN ONE work top jig for up to 900mm worktops.

  • Hard wearing solid laminate 12mm thick jig that cuts both parts of the joint in 15 minutes including setting up.
  • Left hand and right hand corners, 400mm radius penisular joint, 45 degree end cut with slight radius, 45 degree trade corner solution for hob units, 100mm radius corner, 40mm radius corner, 35mm kitchen door hole and 3/4inch BSP hole for mixer taps.
  • Fixed lengths for 400mm, 500mm, 550mm, 600mm, 616mm, 650mm, 700mm and 900mm wide worktops.
  • Cuts up to 40mm thick worktops with or without anti-drip postformed edge.
  • Three open-ended bolt recesses (dog bone style) for 150mm bolts.
  • Engraved lines for short 65mm bolts and worktop cross-cut.
  • 10mm diameter plastic pins with tapered shoulder for tight fit provides three point pin contact to ensure ease of setting up.
  • Engraved markings for identification of pin holes.
    • £134.97
    (ex. VAT)
  • Draining Groove Jig

    Draining Groove Jig

    Draining Groove Jig
    DG/JIG

    For routing draining grooves in solid timber for Belfast type sinks.

  • Made from 12mm hardwearing CNC machined phenolic.
  • Provides a 0.5 degree fall.
  • Grooves at 50mm pitch and 455mm long.
  • Sight marks for lining up.
  • Three removeable sloping runners for support.
  • Cutter diameter check hole.
  • Fixing holes for user made stops for repitition work.

    •  

    Includes:

    £102.26
    (ex. VAT)
  • Lock Jig Large

    Lock Jig Large

    Lock Jig Large
    LOCK/JIG/A

    For routing the face-plate and mortise for larger locks quickly & accurately.

    • Suitable for DDA (Disabilty Discrimination Act) lock size. 20mm x 235mm radius end face plate and 17mm x 170mm mortise.
    • Adaptor plate included to allow smaller templates (239mm x 60mm) to be fitted (as supplied with standard LOCK/JIG).
    • Suitable for doors 34mm to 58mm thick.
    • An auger bit and drill is required to complete deep mortises.

     

    Includes:

  • 1 x Guide bush collar
  • 1 x Face plate template
  • 1 x Mortise template
  • 1 x Template adapter
    • £123.31
    (ex. VAT)
  • Lock Jig

    Lock Jig

    Lock Jig
    LOCK/JIG
    • This jig uses a set of interchangeable templates & with a router will cut the mortise & face-plate recess for popular door locks.
    • For most common sash mortises & dead locks, with up to 3 inch deep mortises & a 7/8 inch or 1inch face-plate.
    • Deeper mortises can be achieved with a suitable size of auger bit.
    • Fast, clean & accurate results on doors 34mm to 58mm thick, even in hardwood.
    • CNC precision manufacturing plates & body.
    • The jig requires a plunge router with a 80mm plunge, fitted with a 30mm guide bush & 12mm diameter long reach cutter.

     

    Includes:

  • 1 x Guide Bush Collar
  • 12 x Face Plate Templates
  • 4 x Mortise Templates
    • £85.21
    (ex. VAT)

    back to top ^